Index
Numbers and Symbols
- 24-bit FC addressing devices
Configuring Fabric Device Nodes
A
- accessing
- iSCSI disksAccessing iSCSI Disks
- iSCSI disks
- automatic failback
- configuringConfiguring Automatic Failback
- configuring
B
- Bit-Masking Format
- Version1 formatBit-Masking Format to Tune Disk Drivers
- Version1 format
C
- cfgadm -al -o show_SCSI_LUNHow to Ensure That LUN Level Information Is Visible
- cfgadm command
- cfgadm -c unconfigureHow to Remove an Fibre Channel Target Port
- cfgadm configureHow to Detect Visible Fabric Devices on an Oracle Solaris System
- cfgadm -c unconfigure
- configure
- fabric-connected devicesConfiguring Fibre Channel Devices
- FC devicesConfiguring Fibre Channel Devices
- multipathing feature
- third-party devicesConfiguring Third-Party Storage Devices
- fabric-connected devices
- configuring
- automatic failbackConfiguring Automatic Failback
- fabric devicesConfiguring Device Nodes Without Multipathing Enabled
- automatic failback
- considerations
- per-port configurationConfiguring Multipathing on a Port Basis
- third-party device configurationConfiguring Third-Party Storage Devices
- per-port configuration
D
- device
- device managementDisk Storage Devices and Device Standards
- device management
- disabling
- discovery
- SAS devicesDynamic Discovery of SAS Devices
- SAS devices
- displaying
- multipathing informationDisplaying Multipathing Information
- specific target portDisplaying All LUs Associated With a Specific Target Port
- multipathing information
E
- enabling
- static discovery methodAdministering Static Configuration Discovery Method
- static discovery method
- error messages
F
- fabric device configurationConfiguring Device Nodes Without Multipathing Enabled
- fabric-connected host ports
- FCoE
- configuring portsManaging FCoE Ports
- creating portsCreating an FCoE Port
- deleting portsDeleting an FCoE Port
- limitationsLimitations of FCoE
- reporting status on portsDisplaying FCoE Port Status
- configuring ports
- Fibre Channel
- listing LUN level informationHow to Ensure That LUN Level Information Is Visible
- listing LUN level information
I
- I/O Multipathing
- initiator ports
- displaying propertiesDisplaying Properties of a Specific Initiator Port
- displaying properties
- iSCSI
- accessing iSCSI disksAccessing iSCSI Disks
- general iSCSI error messagesGeneral iSCSI Error Messages
- modifying iSCSI initiator and target parametersHow to Modify an iSCSI Initiator Node and Target Parameters
- removing discovered iSCSI targets (how to)Removing Discovered Target Devices
- troubleshooting iSCSI configuration problems (how to)Troubleshooting iSCSI Configuration Problems
- accessing iSCSI disks
- iscsiadm modify command
- enabling CHAP (example of)How to Configure CHAP Authentication for an iSCSI Initiator
- enabling or disabling sendtarget discovery methodAdministering sendtargets Discovery Method
- enabling or disabling static or dynamic targets (example of)Removing Discovered Target Devices
- enabling CHAP (example of)
- iscsiadm remove command
- removing static or dynamic targets (example of)Removing Discovered Target Devices
- removing static or dynamic targets (example of)
L
- limitations
- load balancing policy
- load-balancing
- LUN
- SCSI devicesHow to Configure Multiple Multipathed FC Devices
- SCSI devices
M
- modifying
- iSCSI initiator and target parametersHow to Modify an iSCSI Initiator Node and Target Parameters
- iSCSI initiator and target parameters
- mpathadm commands
- initiator ports
- mpt driverDynamic Discovery of SAS Devices
- Multipath Management API plug-in
- propertiesDisplaying Multipathing Information
- properties
- multipathing
- configuring automatic failbackConfiguring Automatic Failback
- configuring device nodesConfiguring Device Nodes With Multipathing Enabled
- configuring third-party storage devicesConfiguring Third-Party Storage Devices
- disabled, device node configurationConfiguring Device Nodes Without Multipathing Enabled
- disabled, multiple device configurationHow to Configure Multiple FC Devices Without Multipathing
- enabling and disablingDisabling and Enabling Oracle Solaris I/O Multipathing
- fabric device node configurationConfiguring Fabric Device Nodes
- manual configurationManually Configuring FC Devices
- troubleshootingTroubleshooting Multipathing Problems
- configuring automatic failback
- multipathing information
- multipathing, enabling and disablingDisabling and Enabling Oracle Solaris I/O Multipathing
N
- Name:Value Format
- JSON-text formatName:Value Pair Format to Tune Disk Drivers
- JSON-text format
P
- per-port configuration
- considerationsConfiguring Multipathing on a Port Basis
- enabling and disabling multipathingConfiguring Multipathing on a Port Basis
- considerations
- persistent binding of tape devicesAbout Persistent Binding
- physical deviceHow to Manually Configure an FC Device Without Multipathing
R
- removing
- discovered iSCSI targets (how to)Removing Discovered Target Devices
- discovered iSCSI targets (how to)
S
- SAS devices
- configurationDisplaying SAS Configuration Information
- dynamic discoveryDynamic Discovery of SAS Devices
- configuration
- sasinfo
- configuration informationDisplaying SAS Configuration Information
- configuration information
- sd driverDynamic Discovery of SAS Devices
- show_SCSI_LUN
- stmsboot command
- system crashesHow to Recover From a System Crash
- system crashes
- Supported HBAsSupported HBAs in FC or FCoE Mode
T
- tape device persistent bindingAbout Persistent Binding
- tape I/O
- multipathingConfiguring Multipathing on Tape Drives
- multipathing
- Target Discovery Method
- sendtargetsTarget Discovery Methods
- StaticTarget Discovery Methods
- sendtargets
- troubleshooting
- iSCSI configuration problems (how to)Troubleshooting iSCSI Configuration Problems
- multipathingTroubleshooting Multipathing Problems
- iSCSI configuration problems (how to)
W
- working with CEE-DCBX